This Page

 

 

What are your beliefs on Installing A Bathtub?

Setting up a bathtub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably hard job. If the old tub is readily obtainable, the task can move quickly; if you have to open up a wall surface to remove the old tub and also position the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the job and also are comfortable attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is far better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will aid you install a brand-new bathtub in your shower room if you have currently purchased a brand-new bathtub and do not need to transform the arrangement of your previous water pipelines.
Your tools and also material list must comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Getting ready for the Installment

First of all, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps system to stop stress on the bath tub.
Fit the flexible tap ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its last placement.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be quite problematic due to the restricted gain access to that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Setting up the Tub

Using the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four little points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub till the level checks out degree.
To set up taps, fit all-time low of the outermost flexible tap adapter to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as also check the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub ought to wait until the tub has actually been used at the very least once as this will certainly settle it right into its final placement.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Protect the faucet in place with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about complications with moisture and also possible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill up the tub with water prior to sealing, to enable the motion experienced when the tub remains in usage. The sealer can split rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is advisable to fit the tiles using water-resistant or water resistant adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed reading our part about How to Install a Bathtub Yourself. Thanks for taking time to read through our content. Appreciated our post? Please share it. Let somebody else check it out. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Visit Our Website